I Tried 7 Ways to Sharpen My Chainsaw Chain. Only One Gave Me Consistent Results
I've run a chainsaw for most of my life. Firewood every fall, storm cleanup, clearing brush around the property. And for most of that time I had the same problem: I could never get my chain sharp the same way twice.
Some weeks it cut great. Other weeks it pulled to one side, smoked, and threw sawdust instead of chips. So over the years I tried just about every way there is to keep a chain sharp. Here's what each one was really like, and the only one I still use today.
1. Taking It to the Sharpening Shop
For years, this was my go-to. The shop did a decent job, but every visit cost me $8–$15 a chain, plus the drive there and back. And my saw sat in the corner for days while I waited.
Worst of all, the chain always went dull right in the middle of a job, never when it was convenient to drive to town.
My verdict: Good results, but slow and expensive. I was paying for the same chain over and over.
2. Just Buying a New Chain
For a while I gave up on sharpening and just bought new chains. Easy, but that's $25 or more every time.
Later I found out most of the chains I'd thrown away weren't worn out at all. They were just dull. I'd been tossing money in the trash.
My verdict: Simple, but the most expensive way to get a sharp chain.
3. A Round File by Hand
Everybody told me a real chainsaw owner files his own chain. A file only costs a few dollars, so I gave it a real try.
The problem is holding the exact same angle and pressure on 50+ teeth. Some teeth came out sharp, some didn't. Some ended up shorter than others, and the saw started pulling to one side.
My verdict: Cheap, but the results were different every single time.
4. An Angle Grinder With a Thin Disc
A buddy swore by this one: put a thin disc on an angle grinder, give each tooth a quick touch, and you're done. It's fast, I'll give it that.
But an angle grinder is way too big and too fast for a tooth that small. Hold it one second too long and the tooth is half gone or turns blue from the heat. After a couple of tries my chain had teeth of every size, and I had to throw it out.
My verdict: The fastest way I found to ruin a good chain.
5. An Electric Bench Grinder
I figured a machine would finally fix it. The bench grinder was fast, but every time I had to take the chain off the saw, set it up on the bench, and plug it in.
It's also easy to hold the wheel on a tooth a second too long and overheat it. And it cost a lot more than I wanted to spend on sharpening.
My verdict: Too much setup and too easy to overdo for a guy who just wants to cut wood.
6. A Rotary Tool With a Sharpening Stone
Then I tried a handheld rotary tool with a chain sharpening stone. Quick, sure.
But I was holding it by eye again, so the angle still wandered. And it's easy to take off too much metal. My chain wore down fast and still didn't cut straight.
My verdict: Fast, but I was back to guessing.
7. The Emblis™ Chainsaw Sharpener
Then I tried the Emblis™ Chainsaw Sharpener. It clamps right onto the guide bar, so the chain stays on the saw. No power, no setup.
The Factory-Angle Lock System holds the grinding bit at the right angle (25°–35°), and the Pawl-Stop Precision System puts every tooth in the same spot before you sharpen it. You just turn the handle and move to the next tooth.
The first time I used it, every tooth came out the same. The saw cut straight, threw big chips again, and the whole chain took me about 5 minutes.
My verdict: The only method that gave me consistent results, every single time.
8. How to Use It in 4 Simple Steps


Emblis™ works with .325" and 3/8" pitch chains on 4" to 22" bars, the size range most homeowner and farm saws fall into, including chains used on Stihl, Husqvarna and Echo saws. Not sure? The pitch is stamped on your bar.
Good to know: Emblis™ sharpens the cutting teeth. Every few sharpenings, also touch up the rakers (depth gauges) with a flat file.
How Emblis™ Compares
Here's how the Emblis™ stacks up against all six other methods I tried.
| Feature | Emblis™ | Hand File | Shop Sharpening |
|---|---|---|---|
| Even Angle | Same on every tooth | Drifts by hand | Machine-ground |
| Chain Stays On | Sharpen on the bar | On the bar | Remove & drop off |
| No Power Needed | Fully manual | Manual | Not your problem |
| Use Anywhere | Woodpile, cabin, truck | Anywhere | Drive to the shop |
| Beginner-Friendly | Guided frame | Takes practice | Done for you |
| Time per Chain | 5–10 minutes | Skill-dependent | Hours to days |
| Cost | One-time purchase | Cheap | $8–15 every visit |
Get Consistent Results Every Time You Sharpen
No more guessing the angle, no more paying the shop, no more throwing away good chains. Clamp it on, turn the handle, and your chain is sharp and even in about 5 minutes.

50% OFF + FREE GIFTS
LIMITED TIME ONLY!
Try it today with a 30-Day Money Back Guarantee!
This page is an advertisement for Emblis™ products. Customer quotes are taken from reviews of the Emblis™ Chainsaw Sharpener on our store. Individual results vary. Always follow your chainsaw manufacturer's safety instructions.
© 2026 Emblis. All Rights Reserved.
| Feature | Emblis™ | Sharpening Shop | New Chain | Round File | File Guide | Bench Grinder | Rotary Tool |
|---|---|---|---|---|---|---|---|
| Same Angle on Every Tooth | Locked angle | Machine-ground | Factory edge | Drifts by hand | Helps a little | Set on the machine | Held by eye |
| Chain Stays On the Saw | Sharpen on the bar | Remove & drop off | Swap it out | On the bar | On the bar | Remove the chain | On the bar |
| No Power Needed | Fully manual | Not your problem | Nothing to sharpen | Manual | Manual | Needs an outlet | Needs power |
| Use Anywhere | Woodpile, cabin, truck | Drive to town | Only with a spare | Anywhere | Anywhere | Workbench only | Near power |
| No Skill Needed | Guided frame | Done for you | Nothing to learn | Takes practice | Still by hand | Easy to overheat | Easy to over-grind |
| Time per Chain | About 5 minutes | Days of waiting | Trip to the store | Skill-dependent | Slow | Setup every time | Fast |
| Cost | One-time purchase | $8–15 every visit | $25+ every time | Cheap | Cheap | Expensive | Tool + stones |








